Mitel 1000 guide Bedienungsanleitung

1 MMiiccrroossoofftt EExxcchhaannggee SSeerrvveerr 22000077 UUnniiffiieedd MMeessssaaggiinngg PPBBXX CCoonnffiigguurraattiioonn NNoott

10 Step 6: Manipulation Routing Setup The first manipulation for the destination prefix will strip the 4-digit number of the Transfer Prefix that wa

11 Step 7: Trunk Group Setup

12 Step 8: TDM BUS Setting

13 Step 9: Trunk Setting Setup

14 Step 10: FAX Setup

15 Step 11: Voice Mail Setup

16 Step 12: General Setup

17 Step 13: • ISDNIBehavior = 1073741824 • EnableMWI = 1 • SubscriptionMode = 1 • EnableDetectRemoteMACChange = 2 • ECNLPMode = 1 • MwiSourceNu

18 Step 14: Reset Mediant 2000 Click Reset to reset the gateway.

19 4.1. Configuration Files The ZIP file includes the following files: 1. AudioCodes Mediant 1000 / Mediant 2000 configuration for TCP environnent

2 Content This document describes the configuration required to setup Mitel 3300 and AudioCodes Mediant 1000/2000 using T1 QSIG as the telephony sign

20 4.2. TLS Setup Step 1: PBX to IP Routing Setup Note: The Proxy IP Address and Name must correspond to the network environment in which the Micr

21 Step 2: SIP Environment and Gateway Name Setup Note: Assign an FQDN name to the gateway (for example, gw1.m2k.audiocodes.com). Any gateway name t

22 Step 3: SIP Environment Setup (Cont.)

23 Step 4: DNS Servers Setup Note: Define the primary and secondary DNS servers' IP addresses so that they correspond to your network environme

24 Step 5: Internal DNS Setup Note: If no DNS server is available in the network, define the internal DNS table where the domain name is the FQDN of

25 Step 6: NTP Server Setup Note: Define the NTP server’s IP address so that it corresponds to your network environment (for example, 10.15.3.50).

26 Step 7: Generate Certificate Setup Use the screen below to generate CSR. Copy the certificate signing request and send it to your Certification Au

27 Step 8: Uploading Certificates Setup The screen below is used to upload the sign certificates. In the “Server Certificate” area, upload the gatew

28 5. PBX Setup Notes Information used for this test case: • Digital VoiceMail ports: T1 QSIG trunk • VoiceMail Hunt Group Pilot: 2690 • VoiceMai

29 Step 1: Ensure PBX is equipped with T1 PRI Module to Support T1 QSIG Use the following path to ensure that the PBX is equipped with a T1 PRI modu

3 1. Components Information 1.1. PBX or IP-PBX PBX Vendor Mitel Model 3300 ICP MX Software Version 7 Telephony Signaling T1 QSIG Additional Not

30 Step 2: Create Class of Service for QSIG Trunks Use the following path to create CoS for QSIG trunk: System Configuration / Trunks / Class of Ser

31 Change the following options to 'Yes': • ANI/DNIS/ISDN Number Delivery Trunk • Call Announce Line • Call Forwarding (External Destina

32 Change the following options to 'Yes': • Display ANI/DNIS/ISDN Calling/Called Number • Display DNIS/Called Number Before Digit Modific

33 Change the following options to 'Yes': • Message Waiting - Audible Tone Notification • ONS CLASS/CLIP: Message Waiting Activate/Deacti

34 Change the following options to 'Yes': • Third Party Call Forward Follow Me Accept • Third Party Call Forward Follow Me Allow • Trunk

35 Step 3: Create Link Descriptor Assignment Use the following path to create Link Descriptor Assignment: System Configuration / Trunks / Digital Tr

36 Step 4: Create a Digital Link Assignment Use the following path to create a Digital Link Assignment: System Configuration / Trunks / Digital Trun

37

38 Step 5: Add MSDN-DPNSS-DASSII Trunk Circuit Descriptor Use the following path to Add MSDN-DPNSS-DASSII Trunk Circuit Descriptor: System Configura

39

4 2. Prerequisites 2.1. Gateway Prerequisites • The gateway also supports TLS (in addition to TCP). This provides security by enabling the encrypt

40 Step 6: Create a Trunk Service Assignment Use the following path to create a Trunk Service Assignment: System Configuration / Trunks / Digital Tr

41 Step 7: Assign Digital Trunks Use the following path to assign Digital Trunks: System Configuration / Trunks / Digital Trunks / ISDN-PRI / Digit

42

43 Step 8: Add Trunk Group for QSIG Use the following path to assign ARS for call routing: System Administration / Automatic Route Selection / Trun

44 Step 9: Add Route Assignment Use the following path to add Route Assignment: System Administration / Automatic Route Selection / Route Assignment

45

46 Step 10: Add ARS Digits Dialed Assignment Use the following path to add ARS Digits Dialed Assignment: System Administration / Automatic Route Se

47

48 Step 11: Option Assignment In System Option Assignment, change the following fields: • Route Optimization Network ID: change to any unique numb

49 5.1. TLS Setup • N/A. 5.2. Fail-Over Configuration • N/A. 5.3. Tested Phones • Mitel SuperSet 4025 5.4. Other Comments None.

5 4. Gateway Setup Notes Step 1: SIP Environment Setup

50 6. Exchange 2007 UM Validation Test Matrix The following table contains a set of tests for assessing the functionality of the UM core feature set

51 Dial the extension for the AA and confirm the AA answers the call. 6 Call Transfer by Directory Search. 6a Call Transfer by Directory Searc

52 Confirm the FAX is received in the user’s inbox. 10 Setup TLS between gateway/IP-PBX and Exchange UM. Windows Certificate Authority (CA). 10

53 6.1. Detailed Description of Limitations Failure Point None Phone type (if phone-specific) Call scenarios(s) associated with failure point L

54 7. Troubleshooting The tools used for debugging include network sniffer applications (such as Ethereal) and AudioCodes' Syslog protocol. The

55 3. To determine the Syslog logging level, use the parameter Debug Level and set this parameter to '5'. 4. Change the CDR Report Level

56 Appendix 1. Dial Pilot Number and Mailbox Login • Dial the pilot number of the UM server from an extension that is NOT enabled for UM. • Confir

57 b. From an External Phone a. From an external phone, dial the extension for a UM-enabled user and leave a voicemail message. b. Confirm the voi

58 • Note: Even though some keys are associated with three or four numbers, for each letter, each key only needs to be pressed once regardless of th

59 • Once it is received in the user’s inbox, use OWA’s Play-On-Phone to dial an internal extension. • Confirm the voicemail is delivered to the co

6 Step 2: Routing Setup Note: The Proxy IP Address must correspond to the network environment in which the Microsoft Unified Messaging server is in

60 9. FAX • Use the Management Console or the Management Shell to FAX-enable a user. • Management Console: a. Double click on a user’s mailbox an

61 12. Message Waiting Indicator (MWI) • Although Exchange 2007 UM does not natively support MWI, Geomant has created a 3rd party solution - MWI2007

7 Step 3: Coder Setup

8 Step 4: Digit Collection Setup

9 Step 5: Supplementary Services Setting Choose any 4-digit number that is not used in the PBX for Transfer Prefix (e.g., 9989).