Mitel 5624 Bedienungsanleitung

MITEL – SIP CoE Technical Configuration Notes Configure the MCD for use with the Ascom i62 SIP Device

14-4940-00152_3 Ascom i62 6 Configuration Notes This section is a description of how the SIP Interop was configured. These notes should give a guidel

14-4940-00152_3 Ascom i62 7 Licensing and Option Selection – SIP Licensing Ensure that the MCD is equipped with enough SIP Device licenses for t

14-4940-00152_3 Ascom i62 8 Class of Service Assignment The Class of Service Options Assignment form is used to create or edit a Class of Service an

14-4940-00152_3 Ascom i62 9 SIP Device Capabilities Assignment This form provides configuration options that can be applied to various types of

14-4940-00152_3 Ascom i62 10 User and Device Configuration On the Mitel MCD, a SIP device can be programmed in the User Configuration form or the Mu

14-4940-00152_3 Ascom i62 11 Enter the Class of Service number and SIP Device Capabilities previously configured in the Service Details tab. F

14-4940-00152_3 Ascom i62 12 The Login PIN is the SIP authentication password and the username is the DN. The Number and Login PIN must match the in

14-4940-00152_3 Ascom i62 13 Reroute Assignment Mitel recommends that call forwarding is programmed using the Call rerouting forms of the MCD. Ca

14-4940-00152_3 Ascom i62 14 If any Call Forwarding Always is required then the Call Rerouting Always Alternative Assignment form would need to be pr

14-4940-00152_3 Ascom i62 15 Ascom i62 Configuration Notes Configuration notes below cover necessary settings to log in an Ascom i62 to a WiFi ne

ii NOTICE The information contained in this document is believed to be accurate in all respects but is not warranted by Mitel Networks™ Corporation

14-4940-00152_3 Ascom i62 16 3. Import the package containing the definition file and the software, File>File Management Figure 13 – Add new p

14-4940-00152_3 Ascom i62 17 5. Insert Ascom i62 WiFi phone into USB cradle. As soon as new device is detected by USB port, the New Device Wizar

14-4940-00152_3 Ascom i62 18 6. Click again Numbers tab and right click on the number in right hand pane. Select Edit. NOTE: Alternatively, you ca

14-4940-00152_3 Ascom i62 19 8. In Edit Parameters screen, expand VoIP node and click General. Select SIP as the VoIP protocol and ensure that

14-4940-00152_3 Ascom i62 20 In left hand pane, click VoIP and then SIP. Enter the IP address/FQDN of the Mitel MCD. If Resiliency is being us

14-4940-00152_3 Ascom i62 21 Figure 19 – VoIP: SIP settings for Silver Resiliency

14-4940-00152_3 Ascom i62 22 9. In left hand pane, click Device and then Message Centre. The “Message Centre number” is required in order the hands

Table of Contents iii OVERVIEW ... 1

14-4940-00152_3 Ascom i62 1 Overview This document provides a reference to Mitel Authorized Solutions providers for configuring the Mitel MCD to

14-4940-00152_3 Ascom i62 2 Tested Features This is an overview of the features tested during the Interop test cycle and not a detailed view of the t

14-4940-00152_3 Ascom i62 3 Resiliency The following table lists the scenarios of resilience supported by this device when connected to the MCD.

14-4940-00152_3 Ascom i62 4 Device Limitations This is a list of problems or not supported features when the Ascom i62 SIP device is connected to the

14-4940-00152_3 Ascom i62 5 Network Topology This diagram shows how the testing network is configured for reference. Figure 1 – Network Topol