Mitel SX-2000 Light Bedienungsanleitung

August 2008 64-0352-01 www.dialogic.com Dialogic® 4000 Media Gateway Series Integration Note Mitel SX-2000 Lightware

Mitel SX-2000 Lightware 10 For the dialplan to be applied to inbound calls, click the Details button of the configured SIP peer and configure the Ad

Dialogic® 4000 Media Gateway Series Integration Note 11 If the ISDN type of numbering flag is set to National, the prefix “N” will be used with the c

Mitel SX-2000 Lightware 12 The following screen shows the first sub rule that converts the E.164 calling number into a 10-digit national number: T

Dialogic® 4000 Media Gateway Series Integration Note 13 The following sub rule converts the E.164 national number into a 10-digit national number wit

Mitel SX-2000 Lightware 14 Once an address map rule is created, it can be applied in three different places. To ease the configuration and troubleshoo

Dialogic® 4000 Media Gateway Series Integration Note 15 Create an address map named Inbound and its four sub rules as shown below:

Mitel SX-2000 Lightware 16

Dialogic® 4000 Media Gateway Series Integration Note 17 Apply the address map inbound rule on the inbound route as follows: 5.2.5 Restarting t

Mitel SX-2000 Lightware 18 6. PBX Setup Notes 6.1 Mitel SX-2000 Lightware This section provides information about the Dialogic® 4000 Media Gateway

Dialogic® 4000 Media Gateway Series Integration Note 19 6.1.1 T1 Interface Administration There are three types of T1 interface administration requ

2 Copyright and Legal Notice Copyright © 2008 Dialogic Corporation. All Rights Reserved. You may not reproduce this document in whole or in part with

Mitel SX-2000 Lightware 20 Select System Forms and press [ESC] then [1] to access the System Forms menu. Step 2: In the System Forms menu, select D

Dialogic® 4000 Media Gateway Series Integration Note 21 Configure the Dimension and Feature Selection as follows: Notes: • Parameters not listed

Mitel SX-2000 Lightware 22 Step 3: In the System Forms menu, select System Configuration and press [ESC] then [2] to edit the System Configuration for

Dialogic® 4000 Media Gateway Series Integration Note 23 • Select the Cabinet number, the Shelf number, and the Slot number in which the T1 Q.SIG line

Mitel SX-2000 Lightware 24 • Set Class of service number: to an unused class of service number. • Press [ESC] then [1] to create the new class of se

Dialogic® 4000 Media Gateway Series Integration Note 25 Step 5: In the Customer Data Entry menu, select Digital Link Forms and press [ESC] then [1] t

Mitel SX-2000 Lightware 26 Configure the form as follows: Note: Parameters not listed below can be left at their default settings. • Set Digital

Dialogic® 4000 Media Gateway Series Integration Note 27 • Set Integrated Digital Access to ISDN Node. • Set QSIG Private Network Access to Yes. • Se

Mitel SX-2000 Lightware 28 • As Link number select 1, and as Cabinet number, Shlf number, and Slot number select the numbers in which the T1 Q.SIG l

Dialogic® 4000 Media Gateway Series Integration Note 29 Step 7: In the Customer Data Entry menu, select System Forms and press [ESC] then [2] to acce

Dialogic® 4000 Media Gateway Series Integration Note 3 1. Scope This document is intended to detail a typical installation and configuration of the

Mitel SX-2000 Lightware 30 Configure the form as follows: Note: Parameters not listed below can be left at their default settings. • Set Route Opt

Dialogic® 4000 Media Gateway Series Integration Note 31 Step 8: In the Customer Data Entry menu, select Trunk Forms and press [ESC] then [1] to acces

Mitel SX-2000 Lightware 32 Note: Parameters not listed below can be left at their default settings. • Set Trunk Circuit Descriptor Number to an unu

Dialogic® 4000 Media Gateway Series Integration Note 33 Step 9: In the Trunk Forms menu, select Trunk Service Assignment and press [ESC] then [2] to

Mitel SX-2000 Lightware 34 Note: Parameters not listed below can be left at their default settings. • Select an unused Trunk Service No. • Set COS (

Dialogic® 4000 Media Gateway Series Integration Note 35 Configure the form as follows: Note: Parameters not listed below can be left at their defa

Mitel SX-2000 Lightware 36 • Press [ESC] then [4] to commit to changes and [ESC] then [1] to confirm the changes. • Press [ESC] then [Q] to return to

Dialogic® 4000 Media Gateway Series Integration Note 37 Note: Parameters not listed below can be left at their default settings. • Set Trunk Group

Mitel SX-2000 Lightware 38 6.1.1.2 Automatic Route Selection (ARS) Step 1: Log into the Mitel SX-2000 Light system. Press [ESC] then [7] to access

Dialogic® 4000 Media Gateway Series Integration Note 39 Select Automatic Route Selection Forms and press [ESC] then [1] to access the ARS Forms men

Mitel SX-2000 Lightware 4 3. Prerequisites 3.1 PBX Prerequisites The PBX must have all supplemental service packages installed for the Q.SIG proto

Mitel SX-2000 Lightware 40 Step 2: In the ARS menu, select Digital Modification Assignment and press [ESC] then [2] to edit the Digital Modification A

Dialogic® 4000 Media Gateway Series Integration Note 41 Note: Parameters not listed below can be left at their default settings. • Select an unused

Mitel SX-2000 Lightware 42 Note: Parameters not listed below can be left at their default settings. • Select an unused Route Number. • Set Trunk G

Dialogic® 4000 Media Gateway Series Integration Note 43 Step 4: In the ARS menu, select Automatic Route Selection Assignment and press [ESC] then [2]

Mitel SX-2000 Lightware 44 Note: Parameters not listed below can be left at their default settings. • Set Leading Digits to a currently unassigned AR

Dialogic® 4000 Media Gateway Series Integration Note 45 • Select the appropriate version of the database based on the version of Mitel SX-2000 Lig

Mitel SX-2000 Lightware 46 • Under Options, select Network-side Interface and Qsig. • Click Update and then Close. Step 3: Configure the PRI Link Ch

Dialogic® 4000 Media Gateway Series Integration Note 47 • Under Line Coding, select B8ZS. • Under Framing, select ESF. • Under Line Build Out, sele

Mitel SX-2000 Lightware 48 Step 5: Configure the Outgoing Call Characteristics as follows: Select Config > Outgoing Call Characteristics. Note:

Dialogic® 4000 Media Gateway Series Integration Note 49 Step 6: Configure the Connection to Remote Sites as follows: Select File > Connect to Rem

Dialogic® 4000 Media Gateway Series Integration Note 5 5. Gateway Setup Notes Steps for setting up the gateway: 1. Configuration of the Dialogic®

Mitel SX-2000 Lightware 50 Step 7: Save the database as follows: Click File > Save > Database. • Set Destinations to PRI Card / Universal NS

Dialogic® 4000 Media Gateway Series Integration Note 51 Click Maintenance > Remote Site Reset. Click the Reset button. Click OK in the Infor

Mitel SX-2000 Lightware 52 7. Microsoft® Office Communications Server 2007 (OCS) Setup 7.1 Steps for configuring Microsoft® OCS Normalization rule

Dialogic® 4000 Media Gateway Series Integration Note 53 Click Add or Edit to create or change a particular rule.

Mitel SX-2000 Lightware 54 In this example, when a user dials any 4-digit number, it will be converted to its E.164 equivalent of +1716639xxxx and t

Dialogic® 4000 Media Gateway Series Integration Note 55 More examples are shown in the following table: Name Phone Pattern Translation Pattern Co

Mitel SX-2000 Lightware 56 This entry routes numbers with or without “+” prefix followed by any digits to Microsoft® Mediation Server dmg4000.bufocs

Dialogic® 4000 Media Gateway Series Integration Note 57 or matched, outbound calls will fail. In this case, Dialogic® Diva® Diagnostics trace will no

Mitel SX-2000 Lightware 58 Under the Communications tab, check the Enable user for Office Communications Server option and then click the Configure bu

Dialogic® 4000 Media Gateway Series Integration Note 59 8. Microsoft® Mediation Server Installation and Configuration 8.1 Installation The gateways

Mitel SX-2000 Lightware 6 Note: The number of TDM circuits varies depending on the used Dialogic® Media Gateway model. For this setup: • Set the pr

Mitel SX-2000 Lightware 60 4. Create the certificate request for the Microsoft® Mediation Server: • Run Deployment Wizard, click step 4. • Select

Dialogic® 4000 Media Gateway Series Integration Note 61 8.2 Configuration From the MMC snap-in, right-click the detected Microsoft® Mediation Server

Mitel SX-2000 Lightware 62 Configure the following settings on the General tab:

Dialogic® 4000 Media Gateway Series Integration Note 63 Click the Next Hop Connections tab and configure the following: The Port entry under PSTN

Mitel SX-2000 Lightware 64 Click the Certificate tab. Select the certificate that will be used to communicate with Microsoft® OCS. Microsoft® Medi

Dialogic® 4000 Media Gateway Series Integration Note 65 Test Number Call Scenario Description Notes Inbound call scenarios 1 Direct call from TDM

Mitel SX-2000 Lightware 66 1. Click one line of your Dialogic® Diva® Media Board in the left pane and click on the toolbar to activate the Basic

Dialogic® 4000 Media Gateway Series Integration Note 67 Examples of Dialogic® Diva® Diagnostics traces for an inbound (TDM to IP) call to Microsoft®

Mitel SX-2000 Lightware 68 <Below is a RX SIP message> 9:16:28.431 1 L 12 00010000-SIPR begin (331 byte) from IP:192.168.0.106 PORT:5060 on soc

Dialogic® 4000 Media Gateway Series Integration Note 69 9:16:30.197 1 L 12 00010000- >ALLOW: UPDATE 9:16:30.197 1 L 12 00010000- >SERVE

Dialogic® 4000 Media Gateway Series Integration Note 7 The Network Interface Configuration will be used by the Diva SIPcontrol software for listeni

Mitel SX-2000 Lightware 70

Mitel SX-2000 Lightware 8 5.2.3 Routing Configuration In the Routing Configuration section, you must create two routes, one for the inbound directi

Dialogic® 4000 Media Gateway Series Integration Note 9 5.2.4.1 Dialplan Configuration Example To create a dialplan, click Add from the Dialplan Con